Safemach Safety Ltd.
Menu
← All insights

20 November 2026

Machinery Directive vs Machinery Regulation: What Changes in January 2027

Machinery Directive vs Machinery Regulation: What Changes in January 2027

Female engineer in hi-vis and hard hat inspecting a guarded automated production line

On 20 January 2027, the Machinery Directive 2006/42/EC is repealed and Machinery Regulation (EU) 2023/1230 applies in full. Machinery placed on the EU market on or after that date must meet the Regulation's requirements. If you have a machine programme in design, manufacture or modification, the practical question is what needs reviewing before the deadline.

Key points for your January 2027 preparations

  • Decide which machines are intended for the EU, Great Britain (GB) and Northern Ireland (NI), and identify the applicable conformity route for each.
  • Review risk assessments, technical files, declarations and contracts for references to the old Directive.
  • Check safety-related software, connectivity, adaptive behaviour and machine modifications.
  • Reassess whether any machinery falls within Annex I's third-party conformity assessment categories.
  • Plan digital instructions and declarations so users can access them reliably.

This is a preparation guide, not another full comparison of the two frameworks. For the legal differences in more detail, read our Machinery Directive and Machinery Regulation comparison and our summary of the key changes in the new EU Machinery Regulation.

What is the deadline, and which machines are affected?

The date to plan around is 20 January 2027. The new Regulation applies to machinery first placed on the EU market, or put into service, from that date. Machinery already placed on the market before then in compliance with the Directive can continue to be made available under the transitional provisions. Keep evidence of when a machine was first supplied to the EU market; a CE mark or a manufacture date alone does not establish that.

For a new machine programme, set the compliance basis according to its intended market and the date it will first be placed on that market, not simply when design or manufacture began.

What should you update in your compliance documents?

Unlike the Directive, the Regulation is directly applicable in EU Member States; it does not rely on national transposition. That makes it important to update the references used across your compliance system, not just the declaration template.

Review:

  • Technical files and risk assessments
  • EU Declarations of Conformity and Declarations of Incorporation
  • Supplier specifications, purchase orders and contracts
  • Design reviews, internal procedures and compliance checklists

Where an EU machine is being placed on the market from 20 January 2027, its documentation should identify Machinery Regulation (EU) 2023/1230, rather than claiming conformity with the repealed Directive. A document update is not, by itself, proof of conformity: the supporting assessment and evidence must also be appropriate to the machine.

How should you review software and connectivity?

The Regulation makes digital safety issues more explicit. A safety function may rely on software or firmware, including logic hosted in a programmable logic controller (PLC) or drive. Identify what each safety-related element does, how it can change, and how you have verified its behaviour. Where the safety-related parts of a control system are designed using EN ISO 13849-1, make sure the design evidence and validation reflect the actual system, not just the component list.

Engineer checking a machine control cabinet and PLC

Also revisit the machine's risk assessment against EN ISO 12100. Consider whether a connection, remote access or external device could affect a safety-related function. Document what happens if a safety-relevant parameter is changed remotely, who is authorised to make that change, and how the machine detects or records relevant interventions. The Regulation includes requirements for protecting safety-critical software and data against corruption.

Does the machine use AI or adaptive behaviour?

The Regulation specifically recognises machinery whose behaviour evolves or adapts, including systems using machine learning in safety functions. Identify whether any part of the machine learns, changes its behaviour or adjusts safety-related decisions after commissioning. Then assess whether that behaviour affects a safety function and whether its limits and foreseeable changes are addressed in the risk assessment and technical documentation.

This does not mean every software-controlled machine is adaptive. Fixed, programmed logic is different from a system that learns or evolves. The distinction matters: certain safety components and embedded systems with fully or partially self-evolving behaviour using machine learning to ensure safety functions are listed in Annex I, Part A, which requires a third-party conformity assessment route.

What counts as a substantial modification?

The Regulation defines a substantial modification made after a machine has been placed on the market or put into service. In broad terms, it is an unplanned physical or digital change that affects safety by creating a new hazard or increasing an existing risk, and that requires specified additional protective measures, for example, guards or protective devices that require changes to the existing safety control system.

A person carrying out a substantial modification takes on manufacturer obligations for the affected machine or part of an assembly. That can include end users, integrators and refurbishers. Before approving an upgrade, consider whether a new risk assessment and conformity assessment are needed; do not assume the original machine's CE marking covers the modified configuration. Repair or maintenance that does not affect compliance is not automatically a substantial modification.

Do you need a third-party conformity assessment?

The Regulation replaces the Directive's Annex IV list with a revised Annex I. Re-check the machine against the new categories rather than relying on its previous classification.

The procedure depends on the category:

  • Annex I, Part A: a specified third-party conformity assessment procedure is required; internal production control alone is not an available route.
  • Annex I, Part B: internal production control may be available if the machine is designed and constructed using the relevant harmonised standards or common specifications covering all applicable requirements. Otherwise, a third-party route is required.
  • Not listed in Annex I: internal production control is the usual route, subject to the Regulation's requirements.

Have the classification reviewed early if a third-party assessment may affect design, programme or supplier decisions.

Can you provide instructions and declarations digitally?

The Regulation permits digital instructions and digital EU Declarations of Conformity, but they must remain accessible and usable. For digital instructions, the manufacturer must explain how to access them, provide a format users can print and save for access when needed, and keep them online for the machine's expected lifetime and for at least 10 years after it is placed on the market.

A user can request a free paper copy of the instructions at the time of purchase; it must be provided within one month. Essential safety information for machinery intended for, or foreseeably used by, non-professional users must be provided in paper form. Digital declarations must also remain accessible online for the expected lifetime and at least 10 years. Put document ownership, hosting, version control and access arrangements in place rather than treating a QR code as the whole solution.

Engineer reviewing a tablet beside a guarded production machine

What does lifecycle safety mean in practice?

Safety needs to be considered beyond design and manufacture. The Regulation's requirements address foreseeable phases such as transport, installation, operation, maintenance, software updates and decommissioning. For a machine programme, this means checking that instructions, controls and risk assessments cover how the equipment will be installed, serviced, updated and eventually taken out of use.

Standards such as EN 60204-1 for electrical equipment of machinery, EN ISO 14119 for interlocking devices and EN ISO 13855 for the positioning of safeguards may be relevant to the design and validation work. The applicable standards depend on the hazards and safeguarding solution.

What do we see companies overlook?

A machine being CE-marked in 2026 is not automatically ready for every 2027 EU placement. If it was placed on the EU market before the date, transitional provisions may apply; if a new machine is first placed on the market from 20 January 2027, its conformity basis needs to meet the Regulation.

We also see safety functions implemented in standard PLCs or drives without a clear record of their purpose, validation or change control. Another risk is upgrading machinery, reapplying a CE mark and assuming that this closes the compliance question. The nature and safety impact of the modification need to be assessed first.

A practical order of work before January 2027

  1. Map machine programmes and markets. Record intended destinations and expected first placement dates.
  2. Triage higher-risk projects. Check Annex I categories and identify any need for third-party assessment.
  3. Review risk assessments. Address safety-related software, connectivity, adaptive behaviour and foreseeable lifecycle phases.
  4. Assess planned modifications. Decide whether each change could meet the substantial-modification definition and identify who holds the resulting manufacturer obligations.
  5. Update technical evidence. Revise applicable standards, control-system validation, technical files and conformity declarations.
  6. Prepare digital documentation. Ensure instructions and declarations are correctly versioned, accessible and supported by the required paper-copy arrangements.
  7. Check the market route. Agree the relevant conformity and marking position for EU, GB and NI with your suppliers and project team.

What does this mean for UK manufacturers and importers?

The Supply of Machinery (Safety) Regulations 2008 continue to govern machinery in GB. The instrument that amends them is The Supply of Machinery (Safety) (Amendment etc.) and the EU Machinery Regulation (Enforcement etc. in Northern Ireland) Regulations 2026 (SI 2026/867), made on 22 July 2026 and in force on 20 January 2027. From that date it amends the Supply of Machinery (Safety) Regulations 2008 as they apply in Great Britain so that machinery meeting Regulation (EU) 2023/1230 can be placed on the GB market, and it revokes the 2008 Regulations in Northern Ireland only, where the EU Machinery Regulation applies under the Windsor Framework. GB recognises machinery conforming to Regulation (EU) 2023/1230 as one route alongside CE and UKCA; the GB framework does not automatically mirror the EU Regulation. CE marking remains recognised indefinitely for machinery on the GB market under The Product Safety and Metrology etc. (Amendment) Regulations 2024, and UKCA marking is not mandatory.

Businesses supplying more than one market should therefore confirm the applicable requirements and marking route for each destination. Do not assume that one conformity file or marking decision automatically covers all markets.

Safemach supports manufacturers, importers and end users with CE marking of machinery, CE/UKCA audits and machinery risk assessments. Where changes to a machine's safeguarding or control system are needed, our engineers can also support the design and installation of machinery safety systems, including SISTEMA validation to EN ISO 13849-1. To discuss a machine programme or planned modification, contact Safemach and speak with a safety engineer.